- #Tc hawken stock crack from the wedge pin screw hole manuals
- #Tc hawken stock crack from the wedge pin screw hole Patch
- #Tc hawken stock crack from the wedge pin screw hole full
Push the three barrel wedge keys past the underlugs, and the barrel will lift and unhook from the tang, instantly, without tools, for easy cleaning after a day of shooting. Stocked in figured tiger stripe maple, this nice rifle is strikingly handsome. Brown, who built the nice rifle shown above. Track's best early fullstock Hawken Rifle parts were selected by the by noted gunmaker J.E. Let us know it you need some more help.Flintlock, with 1" straight octagon barrel up to 42" in lengthīuild Track's Early Hawken fullstock rifle kit, Then reshape the bevel on the wedge pin with a file. This way you won't pull the screws out and strip the holes in the stock. I suggest that you take the two little screws out of the opposite oval that the wedge pins go through and then finish removing the pins. I don't know why anyone would have intentionally flattened the beveled end unless they didn't intend on ever taking them out.ĭid you get them out far enough to remove the barrel? Did you get them through the one brass oval screwed onto the stock that it goes through? If you got it through that it should go through the mating slot under the barrel. It is about 1 - 1 1/4" long and flat (the flat portion is about 3/8" wide x 3/32" thick). The wedge pin is simply a piece of brass that has an oval or rectangular head about 1/2" x 1/4". I don't know what you mean by buggered up. Jfg - the wedge pins should come out fairly easily. Sounds like a lot of info but once you do it a couple times, its easy. You can bend them slightly if you must by laying on a flat surface and tipping them in the center with a mallet until you get the proper fit. A firm thumb pressure should be all that is needed. You don't want them to fall out nor do you want to have to tap them in with a mallet. Try flipping them over if they are too loose or too tight. Note: the wedge pins should be snug but not too tight. Then coat the inside of the bore with either bore butter or a high quality gun oil. Apply some antisieze to the nipple threads and reinstall. Dry and give the entire barrel a light coat of oil.
#Tc hawken stock crack from the wedge pin screw hole Patch
Dry the barrel thoroughly (It will be hot so a couple dry patches followed by an alcohol patch and dry patch should be sufficient.) Clean the outside of the barrel around the nipple area to remove any residue. When you are satisfied that the barrel is clean, you can pour hot clean water down the muzzle to rinse it out. This will create a vacuum and start sucking water out of the container and flush the barrel. Once you reach the bottom you can begin working the patch in longer strokes. Start working the patch throught the bore. Put the appropriate jag on the ramrod or range rod and wet a patch and place it over the muzzle. When you get the nipple off, put the breach end of the barrel back into the water. I am assuming you have a percussion cap so yo will need a nipple wrench or a small wrench to take off the nipple.
#Tc hawken stock crack from the wedge pin screw hole full
If you're going to clean it, get a bucket or 3 lb coffee can and fill it about 3/4 full with hot soapy water (dawn dish detergent is great) and put the barrel in breach end first and let it soak for a few mins.
And when he said to lift the barrel straight up - lift up as if you were lifting the muzzle 90 degrees of the stock (not straight out from the butt). Jfg - I assume you're lloking to clean it.
#Tc hawken stock crack from the wedge pin screw hole manuals
And then wipe the outside of all the metal parts off and your done.ĬVA does have on line manuals you can download in PDF format. Be fore to close the hammer or cock on the flint lock to take the pressure off the springs when you store it. Kind of squeeze the barrel to the stock and replace the wedge pins, ramrod, and your have re assembled it. If you done it right, the barrel and tang will close real tight and the barrel can be put back into the stock. Put the button in the tang and as you move it down it will slide back ward into the tang and lock in there as the barrel moves down into the stock. When your ready to put the barrel back, just reverse the steps. Pay special attention to the back end of the barrel and don't miss that. Take a Q-tip and put some oil in that and be sure to wipe inside the tang lock hole. The button on the end of the barrel goes in and under the lip of the tang (the part that is screwed to the back of the stock that the barrel locks into).Īfter you have the barrel off, its easy to clean. Its still a hooked breech but looks a little different. You CVA might have what's known as a button breech. Now grab the barrel in front of the wood stock. Then cock your hammer all the way back off the nipple or if its a flintlock, cock that flintlock to move it off the frizzen. Remove the ramrod as well from the thimble rib as this can hold the barrel in. Yours has two wedge pins your saying? To remove the barrel knock out all the way both wedge keys.
0 kommentar(er)
